| 當前位置：首頁->方案設計 |
|
| TLUX385A 200W 4路LED驅動解決方案 |
|
|
| 文章來源： 更新時間：2014/10/30 14:57:00 |
在線咨詢： |
| |
ST公司的TLUX385A是用于照明和電源轉換的數字控制器,具有六個可編PWM發生器,96MHz PLL和DALI,它的心臟是狀態機驅動(SMED),能工作于六個單獨配置的PWM時鐘,最大分辨率1.3ns,用來驅動多個LED串,功率因素修正,大功率調光LED的半橋諧振轉換器和HID燈鎮流器的全橋控制器.本文介紹了TLUX385A主要特性,框圖, STLUX385A SEMD架構主要特性和框圖,以及200W數字4路LED評估板STEVAL-ILL057V1主要特性,電路圖和材料清單,PCB設計圖.
Digital controller for lighting and power conversion applications with 6 programmable PWM generators, 96 MHz PLL, DALI
The STLUX385A device is part of the STLUX™ family of STMicroelectronics® digital devices tailored for lighting and power conversion applications. The STLUX385A has been successfully integrated in a wide range of architectures and applications, starting from simple buck converters for driving multiple LED strings, boost for power factor corrections, half-bridge resonant converters for high power dimmable LED strings and up to full bridge controllers for HID lamp ballasts.
The heart of the STLUX385A device is the SMED (state machine event driven) technology which allows the device to operate six independently configurable PWM clocks with a maximum resolution of 1.3 ns. A SMED is a powerful autonomous state machine, which is programmed to react to both external and internal events and may evolve without any software intervention. The SMED reaction time can be as low as 10.4 ns, giving the STLUX385A the ability of operating in time critical applications. The SMED offers superior performance when compared to traditional, timer based, PWM generators.
Each SMED is configured via the STLUX385A internal microcontroller. The integrated controller extends the STLUX385A reliability and guarantees more than 15 years of both operating lifetime and memory data retention for program and data memory after cycling.
A set of dedicated peripherals complete the STLUX385A:
4 analog comparators with configurable references and 50 ns max. propagation delay. It is ideal to implement zero current detection algorithms or detect current peaks.
10-bit ADC with configurable op amp and 8-channel sequencer.
DALI: hardware interface that provides full IEC 60929 and IEC 62386 slave interface.
96 MHz PLL for high output signal resolution.
TLUX385A主要特性:
6 programmable PWM generators (SMEDs) (state machine event driven)
– 10 ns event detection and reaction
– Max.1.3 ns PWM resolution
– Single, coupled and two coupled operational modes
– Up to 3 internal/external events per SMED
DALI (digital addressable lighting interface)
– Interrupt driven hardware encoder
– Bus frequency: 1.2, 2.4 or 4.8 kHz
– IEC 60929 and IEC 62386 compliant plus
24-bit frame extension
– Configurable noise rejection filter
– Reverse polarity on Tx/Rx lines
4 analog comparators
– 4 internal 4-bit references
– 1 external reference
– Less than 50 ns propagation time
– Continuous comparison cycle
8 analog-to-digital converters (ADCs)
– 10-bit precision, with operational amplifier to extend resolution to 12-bit equivalent
– Sequencer functionality
– Input impedance: 1 M
– Configurable gain value: x 1 or x 4
Integrated microcontroller
– Advanced STM8® core with Harvard architecture and 3-stage pipeline
– Max. fCPU: 16 MHz
Memories
– Flash and E2PROM with read while write
(RWW) and error correction code (ECC)
– Program memory: 32 Kbytes Flash; data retention 15 years at 85 ℃ after 10 kcycles at 25 ℃
– Data memory: 1 Kbyte true data E2PROM; data retention:15 years at 85 ℃ after 100 kcycles at 85 ℃
– RAM: 2 Kbytes
– ROM: 2 Kbytes
Clock management
– Internal 96 MHz PLL
– Low-power oscillator circuit for external crystal resonator or direct clock input
– Internal, user-trimmable 16 MHz RC and low-power 153.6 kHz RC oscillators
– Clock security system with clock monitor
Basic peripherals
– System and auxiliary timers
– IWDG/WWDG watchdog, AWU, ITC
Reset and supply management
– Multiple low-power modes (wait, slow, autowakeup, Halt) with user definable clock gating
– Low consumption power-on and powerdown reset
I/O
– 12 multifunction bidirectional GPIO with highly robust design, immune against current injection
– 6 fast digital input DIGIN, with configurable pull-up
Communication interfaces
– UART asynchronous with SW flow control
– I2C master/slave fast-slow speed rate
Operating temperature
– -40 ℃ up to 105 ℃.
圖1. TLUX385A框圖
STLUX385A架構
The STLUX385A device generates and controls PWM signals by means of a state machine, called SMED (state machine event driven).
The core of the device is the SMED unit: a hardware state machine driven by system events. The SMED includes 4 states (S0, S1, S2 and S3) available during running operations. A special HOLD state is provided as well. The SMED allows the user to configure, for every state, which system events trigger a transaction to a new state. During a transaction from one state to the other, the PWM output signal level can be updated.
Once a SMED is configured and running, it becomes an autonomous unit, so no interaction is required since the SMED automatically reacts to system events.
Thanks to the SMED’s 96 MHz operating frequency and their automatic dithering function, the PWM maximum resolution is 1.3 ns.
The STLUX385A device has 6 SMEDs available. Multiple SMEDs can operate independently from each other or they can be grouped together to form a more powerful state machine.
The STLUX385A also integrates a low-power STM8 microcontroller which is used to configure and monitor the SMED activity and to supply external communication such as DALI. The STM8 controller has full access to all the STLUX385A subsystems, including the SMEDs. The STLUX385A device also features a sequential ADC, which can be configured to continuously sample up to 8 channels.
圖2. STLUX385A SEMD架構圖
STLUX385A SEMD架構主要特性:
Configurable state machine generating a PWM signal
More than 10.4 ns PWM native resolution
Up to 1.3 ns PWM resolution when using SMED dithering
6 states available in each SMED: IDLE, S0, S1, S2, S3 plus a special HOLD state
Transactions triggered by synchronous and asynchronous external events or internal timer
Each transaction can generate an interrupt
Fifteen registers available to configure the state machine behavior
Four 16-bit configurable time registers, one for each running state (T0, T1, T2, T3)
Internal resources accessible through the processor interface
Eight interrupt request lines
帶電流穩壓和調光的200W數字4路LED評估板STEVAL-ILL057V1
The STEVAL-ILL057V1 product evaluation board is a complete and configurable solution for managing four independent high-brightness LED channels using the STLUX385A digital controller.
The STLUX385A is part of STMicroelectronics’ Masterlux™ family and embeds advanced peripherals tailored to generate high resolution PWM signals (SMED).
The STEVAL-ILL057V1 implements inversed buck topology to drive each LED channel. The SMED technology integrated in the STLUX385A regulates the LED current, exploiting the fixed offtime (FOT) principle. Each channel can generate output current in the range of 250 mA to 1 A.
The number of LEDs, the current and the PWM dimming point can be set through the command interpreter, accessible via the serial interface.Dimming can also be manually adjusted via the three on-board buttons.
The evaluation board can be optionally controlled via a DALI interface. The DALI connection board is available separately (part number STEVALILM001V1).
The STLUX385A DALI software drivers and application firmware are available.
200W數字4路LED評估板STEVAL-ILL057V1主要特性:
• Based on the STLUX385A digital controller
• Up to 200 W
• 4 LED channels
• Adjustable LED current and dimming
• Adaptive voltage compensation
• Real-time fault detection and protection (e.g: short or open circuit)
• Serial interface
• DALI (optional)
• RoHS compliant
圖3. 200W數字4路LED評估板STEVAL-ILL057V1外形圖
圖4. 200W數字4路LED評估板STEVAL-ILL057V1電路圖(1)
圖5. 200W數字4路LED評估板STEVAL-ILL057V1電路圖(2)
圖6. 200W數字4路LED評估板STEVAL-ILL057V1電路圖(3)
200W數字4路LED評估板STEVAL-ILL057V1材料清單:
STEVAL-ILL057V1 PCB設計圖見: |
| |
|
|
|
|
|
| |
|
| |
|
|
