| 當前位置：首頁->方案設計 |
|
| AT86RF233 REB233-XPRO擴展板無線收發器評估方案 |
|
|
| 文章來源： 更新時間：2015/1/9 13:23:00 |
在線咨詢： |
| |
Atmel 公司的AT86RF233是富有特性極低功耗的單片2.4GHz無線收發器,接收器靈敏度-101dBm,可編程輸出功率從-17dBm到+40dBm, 工作電壓1.8V-3.6V,深度睡眠的功耗為0.02uA,主要用于 2.4GHz IEEE 802.15.4和ZigBee系統,RF4CE系統,能量收獲系統,6LoWPAN系統,工業控制,住宅區和商業自動化,醫療保健,消費類電子和PC外設等.本文介紹了AT86RF233主要特性,方框圖,基本和擴展特性應用電路,以及REB233-XPRO擴展板主要特性,框圖,電路圖,材料清單和 PCB設計圖.
The Atmel AT86RF233 is a feature rich, extremely low-power 2.4GHz radio transceiver designed for industrial and consumer ZigBee/IEEE 802.15.4, RF4CE, 6LoWPAN, and high data rate 2.4GHz ISM band applications.
The AT86RF233 is a true SPI-to-antenna solution. All RF-critical components except the antenna, crystal, and de-coupling capacitors are integrated on-chip. MAC and AES hardware accelerators improve overall system power efficiency and timing. Therefore, the AT86RF233 is particularly suitable for applications like:
• 2.4GHz IEEE 802.15.4 and ZigBee systems
• RF4CE systems
• Energy Harvesting systems
• 6LoWPAN systems
• Wireless sensor networks
• Industrial Control
• Residential and commercial automation
• Health care
• Consumer electronics
• PC peripherals
AT86RF233主要特性:
• High Performance RF-CMOS 2.4GHz radio transceiver targeted for IEEE® 802.15.4, ZigBee®, RF4CE, 6LoWPAN, and ISM applications
• Industry leading link budget:
• Receiver sensitivity -101dBm
• Programmable TX output power from -17dBm up to +4dBm
• Ultra-low current consumption:
• DEEP_SLEEP = 0.02μA
• TRX_OFF = 300μA
• RX_ON = 11.8mA (LISTEN)
• Smart Receiving Techniques enable further current reduction in LISTEN mode between 10 to 50% from 11.8mA
• Desensitation will enable further reduction up to 1mA
• BUSY_TX = 13.8mA (at max. transmit power)
• Ultra-low supply voltage (1.8V to 3.6V) with internal regulator
• Support for coin cell operation
• Optimized for low BoM Cost and ease of production:
• Few external components necessary (crystal, capacitors and antenna)
• Easy to use interface:
• Registers, frame buffer, and AES accessible through fast SPI
• Only two microcontroller GPIO lines necessary
• One interrupt pin from radio transceiver
• Clock output with prescaler from radio transceiver
• Radio transceiver features:
• 128-byte FIFO (SRAM) for data buffering
• Fully integrated, fast settling PLL to support Frequency Hopping
• Supports 500kHz channel spacing
• Battery monitor and Fast Wake-Up Time < 0.4msec
• Special IEEE 802.15.4™ 2011 hardware support:
• FCS computation and Clear Channel Assessment
• RSSI measurement, Energy Detection and Link Quality Indication
• MAC hardware accelerator:
• Automated acknowledgement, CSMA-CA and retransmission
• Automatic address filtering
• Automated FCS check
• Extended feature set hardware support:
• AES 128-bit hardware accelerator
• Antenna Diversity and RX/TX indication
• Supported PSDU data rates: 250kb/s, 500kb/s, 1000kb/s and 2000kb/s
• True Random Number Generation for security application
• Reduced Power Consumption modes
• Time and phase measurement support
• Industrial and extended temperature range:
• -40°C to +85°C and -40℃ to +125℃
• I/O and packages:
• 32-pin Low-Profile QFN Package 5 x 5 x 0.9mm³
• RoHS/Fully Green
• Compliant to EN 300 328/440, FCC-CFR-47 Part 15, ARIB STD-66, RSS-210
• Compliant to IEEE 802.15.4 2003/2006/2011
圖1. AT86RF233框圖
圖2. AT86RF233應用電路圖
圖3. AT86RF233擴展特性應用電路圖
REB233-XPRO擴展板
This user guide describes how to get started with the Atmel® REB233-XPRO extension board.
The extension boards is targeted for evaluating the features of the Atmel AT86RF233 radio transceiver.
Xplained Pro is an evaluation platform that provides the full Atmel microcontroller experience. The platform consists of a series of Microcontroller (MCU) boards and extension boards that are integrated with Atmel Studio, have Atmel Software Framework (ASF) drivers and demo code, support data streaming and more.
Xplained Pro MCU boards support a wide range of Xplained Pro extension boards that are connected through a set of standardized headers and connectors. Each extension board has an identification (ID) chip to uniquely identify which boards are mounted on a Xplained Pro MCU board.
圖4. REB233-XPRO擴展板外形圖
圖5. REB233-XPRO擴展板電路圖(1)
圖6. REB233-XPRO擴展板電路圖(2)
REB233-XPRO擴展板材料清單:
圖7. REB233-XPRO擴展板PCB設計圖(頂層)
圖8. REB233-XPRO擴展板PCB設計圖(底層) |
| |
|
|
|
|
|
| |
|
| |
|
|
